Schedule Appointment

 

What are your concepts on How to Install a Bathtub Yourself?

Installing a tub isn't specifically rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately difficult task. If the old tub is conveniently accessible, the project can relocate immediately; if you have to open a wall to eliminate the old tub and position the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have qualified on your own for the task as well as are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed project, it is far better to think about employing one before you start. Chances are you might need an expert plumber to make tube links.
This post will help you set up a brand-new bathtub in your bathroom if you have currently purchased a brand-new bathtub as well as do not need to transform the plan of your previous water system pipelines.
Your tools as well as material checklist need to consist of the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to replace old taps with new ones as a part of your installation, after that the first thing you ought to do is detach the water supply. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the limited gain access to that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, use the same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, then you will require a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the faucet in position with the producer given backnut. Once the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet ports. The former type ought to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Mounting the Tub

Utilizing both wood boards under its feet, place the bath tub in the needed position. The wood boards are practical in equally spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bathtub till the level checks out degree.
To install taps, fit the bottom of the furthest flexible faucet port to the ideal supply pipe by making a compression sign up with; after that do the same for the other faucet.
Switch on the water supply as well as inspect all joints and also new pipework for leakages and also tighten them if necessary. Fill the bathtub as well as additionally check the overflow outlet as well as the normal outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and securing around the bathtub must wait till the tub has been made use of at the very least once as this will resolve it right into its final position.

 

 

Getting ready for the Installment

First of all, the sustaining framework supplied with the bath should be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final placement.

 

 

Tiling Around the Tub

In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to break a rigid seal, creating the water to pass through the wall surface in between the bath as well as the tiling, bring about difficulties with moisture and also possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, and are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to allow for the movement experienced when the bathtub is in usage. The sealer can break fairly very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or water resistant sticky and also cement.

 

Bathtub Installation

 

How Important Is A Bathtub To Your Home?

 

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

 

Install Piping Before Tub

 

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

 

Position the Tub

 

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

 

Assemble Drain Connections

 

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

 

Place a Pipe For the Shower Head

 

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

 

Attaching Hot and Cold Water Lines

 

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

 

Install the Spout

 

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

 

Check For Leaks

 

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

 

estore the Bathroom Wall

 

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

 

I'm very serious about Tools You Need to Install a New Bathtub and I'm hoping you enjoyed my entry. Sharing is caring. Who knows, you may just be doing someone a favor. We enjoy reading our article about How to Install a Bathtub.

Perfect solution? Dial!